UKEN

Thank you!

Our manager will contact you as soon as possible

S-20 PLASTER "FASSADE-SILIKON"

For external and internal works
description:

S-20 - Ready to use structural plaster based on silicone resin. It is used as a finishing coating of "bark" type on the facades.

features:
  • For internal and external work
  • High atmospheric resistance
  • Protected from fungal and algal damages
  • Water repellent
  • Grain size 2.0 mm
order

Usage

Ready to use structural plaster based on silicone resin. It is used as a finishing coating of "bark" type on the facades. It is intended for application on mineral plasters, concrete, prepared brick basis, surfaces of systems of thermal insulation of facades, drywall, chipboard, QSB and OSB. Recommended for decoration of facades in places with high aggressive influence. Can be used to create durable wear-resistant coatings in the middle of the premises. Not suitable for surfaces with salt spots, as well as for surfaces made of plastic.

preparing basis

Preparation of the base is carried out in accordance with DBN B.2.6-22-2001 and DSTU-N B A.3.1-23: 2013. The surface should be clean, dry and durable. Separation, old coatings and oil contamination carefully removed. Inequalities are aligned with a putty. Cement plaster should be kept for a minimum of 28 days, putty surfaces - at least 3 days, the surface of insulation systems - 7 days. All surfaces must be treated with silicone soil paint of TM "BUDMIKS" GF-2. When applied to the system of facade insulation, the complex system includes, as a minimum: a system glue composition, system insulation panels, a system reinforced coating consisting of one or more layers, of which at least one must be reinforced, a systemic first coat, a system decorative finish (silicone decorative plaster, paint, etc.).

preparing

If necessary, add up to 2% water and mix without breaking. Apply a stainless steel spatula to the wall on the wall to the thickness of the grain. Hold for a while and, until the plaster is mild, to structure the plastic grater in the desired direction (up, down, left-to-right or circular movements).

Technical parameters

Usage guide

  • FASSADE-SILIKON PREMIUM S-20
    TU 20.3-31158382-0522017
  • Consumption
    Approximately 2.6 kg / m² on an equal surface.
  • Depending on the grains and the level of the surface
    the flow rate may vary.
  • Drying time
    24 hours at + 20 ° C and humidity 65%.
  • Full drying and repainting
    2-3 days later.
  • Application temperature
    from + 5 ° C to + 30 ° C and humidity below 80%.
  • Guaranteed storage life in hermetically sealed packaging
    24 months.
  • Packaging
    Bucket 25 kg.

If necessary add up to 2% water and mix, not knocking down. Apply a stainless steel spatula to the wall on the wall to the thickness of the grain. Hold for a while and, until the plaster is mild, to structure the plastic grater in the desired direction (up, down, left-to-right or circular movements). The shutter speed depends on the humidity and air temperature. Increased humidity and reduced temperature require longer exposure of the deposited layer to the structuring. Conversely, with less humidity and high temperature, the time between applying a plaster layer and its structuring decreases. If necessary, split large surfaces into several small ones or work in a group. The entire surface should be treated with the wet-wet method. When applying plaster it is not allowed to clean the working tool from excess plaster with water. Clean only with cloth. Do not apply under direct sunlight. Protect from precipitation and frost to complete hardening of plaster.

COSTS: Approximately 2.6 kg / m² on an equal surface. Depending on the graininess and the level of the surface, the flow rate may vary.

FEATURES: To provide plaster, additional antifungal properties are recommended to be added before applying an anti-freeze admixture to the plaster and mix thoroughly.

EXPANSION TIME: 24 hours at + 20 ° C and humidity 65%. Complete drying and repainting in 2-3 days.

SAFETY AND ADMINISTRATION: Keep out of the reach of children. In case of contact with eyes immediately wash them with clean water. Do not pour plaster into sewers, ponds or on the ground. The remnants of dried plaster are disposed of as ordinary construction waste.

COLORING: Possible by any dye intended for coloring acrylic paints, as well as specialized equipment for toning paints. Put plaster on one plane, having one batch number, or mix thoroughly the products from different batches together! When drying plaster, depending on weather conditions, there may be discrepancies in shades. This does not affect the product's functional qualities. To eliminate unevenness in shades, it is necessary to paint the plaster with a facade paint of a corresponding color.

STORAGE: In a tightly closed container in a cool place, at a temperature from + 5 ° C to + 30 ° C. It is necessary to prevent the direct sunlight from reaching the packaging. Guaranteed storage life in hermetically sealed factory packaging - 24 months

Download full catalog in PDF format
download