UKEN

Thank you!

Our manager will contact you as soon as possible

GLUE 23 "SUPER FACADE 2 in 1"

For external and internal works
description:

K-23 - fiber-reinforced polymer-cement modified dry adhesive mixture.

features:
  • For external and internal works
  • Frost resistant, water-repellent
  • Eco-friendly
  • Easy to use
order

Usage

K-23 - fiber-reinforced polymer-cement modified dry gluing mixture based on high-quality cement and modifiers of leading European manufacturers for fastening of plates of expanded polystyrene foam (including extruded) and mineral wool on concrete, brick, plaster surfaces and implementation of a waterproof protective layer when installing insulation systems buildings For external and internal works.

preparing basis

Preparation of the base to be performed in accordance with the requirements of DBN B.2.6-22-2001 and DSTU-N B A.3.1-23: 2013. The base should be strong, even, cleaned of dust, dirt, residual paints, oils, etc. Remove the plaster that is lagging behind the base. Clean the surface of the wall with or without plaster by mechanical means, for example, using a wire brush and wash with water under pressure. Inequalities greater than 10 mm and the place where the plaster was removed, aligned with the use of plaster Ш-4 «UNIVERSAL». Surfaces with increased water absorption moisten or process primer T-1 "PREMIUM", according to the instruction

preparing

The glutinous mixture is to be prepared at a rate of 0.22-0.24 liters of water per 1 kg of dry mixture, gradually filling the dry mixture from the bag into a tank with clean water while simultaneously manual or mechanical (at low revolutions), stirring until homogeneous mass is formed without lumps. Stand for 5 minutes Mix the mortar again.

Technical parameters

Usage guide

  • Approximate dilution for bonding plates
    4.5-6.0 kg / m2;
  • Approximate dilution for reinforced layer
    4,5-5,5 kg / m2 at a layer thickness of 3-4 mm
  • Volume of water for mixing
    0,22 - 0,24 l / kg (about 6 l / bag)
  • Suitability of the mortar mixture
    not less than 2,5 hours.
  • Water absorption coefficient
    not more than 0,5 kg / m2 / h.
  • Correction time
    not less than 10 min.
  • Shrinkage
    no more than 1.5 mm / m
  • Strength of grip with concrete base
    not less than 0,5 MPa
  • Vapor permeability
    not less than 0,1 mg / mhh. x pa
  • Frost resistance
    not less than 50 cycles
  • Performance temperature
    from + 5 ° C to + 30 ° C
  • Packaging
    paper bags of 25 kg

Gluing heat insulation boards

When gluing the plates at the level of the surface of the glue, use a spatula with teeth 10 × 10 mm, evenly distributing the mass across the surface. When sticking to uneven bases at a distance of 3 cm from the edge of the plate, apply glue in a continuous strip 3-4 cm wide, arranging gaps to prevent the formation of air cork. On the rest of the plate surface 50 × 100 cm lay 3-4 buckets of glue. Plates should be glued not less than 50% of their surface area. Extruded foam plates pre-treated with rough sandpaper to provide roughness. To change the glue apply to the entire surface of the slab, pre-lubricating it to ensure a reliable grip. After applying the glue, the plate should be applied to the wall to the designated place and pressed to obtain an equal plane with adjoining slabs. Remove excess glue - there should be no residue on the ends. Heat insulation boards stick with spill threads. Mechanical fastening and performance of waterproofing cover should be carried out not earlier than 3 days after sticking of plates.

Implementation of a waterproof reinforced layer

Apply glue to the surface of the plate using a spatula with equal edges with continuous stripes on the width of the reinforcing mesh. Spatula with teeth 10 × 10 mm to align the thickness of the layer of glue. Using a spatula with an even edge, squeeze the net and evenly shuffle. The mesh should be completely recessed in glue, evenly stretched, without folds and blistering. Overlapping adjacent strips of the grid should be at least 10 cm. The thickness of the resulting coating - 3-4 mm. The application of decorative plaster should be carried out not earlier than three days after the implementation of the waterproofing layer.

When performing assembly, reinforcement and finishing work, it is necessary to cover the facade with a protective grid for protection from direct sunlight, wind and rain, and in windy or hot weather periodically (at least 3 times in 12 hours), to further moisten the applied coatings. The temperature of the air, the substrate and the materials used must be in the range from + 5 ° C to + 30 ° C.

The technical characteristics of the mixture and the recommendations for use were determined under standard conditions (t = 20 ° С, humidity 65%) and in real conditions may change.

STORAGE:

Store in dry containers in unharmed containers. Warranty period - 12 months from the date of production.

WARRANTY OF MANUFACTURER:

The manufacturer guarantees the conformity of the products with the declared technical characteristics, subject to the rules of transportation, storage and compliance with this instruction.
The manufacturer does not bear responsibility for the unauthorized use of the material.

Download full catalog in PDF format
download