UKEN

Thank you!

Our manager will contact you as soon as possible

K-9 GLUE "FRONT-Universal"

For systems of insulation of type "Betol"
description:

K-9 - polymer-cement modified dry mix with fillers and microfibre for fastening of heat-insulating slabs of non-corrosive concrete on concrete, brick, plaster surfaces and performance of waterproofing reinforced layer in systems of insulation of facades of type "BETOL".

features:
  • For external and internal works
  • Atmospheric resistance
  • Eco-friendly
  • Easy to use
order

Usage

K-9 - polymer-cement modified dry mix with fillers and microfibre for fastening of heat-insulating slabs of non-corrosive concrete on concrete, brick, plaster surfaces and performance of waterproofing reinforced layer in systems of insulation of facades of type "BETOL".

preparing basis

The base should be solid, level, cleaned of contaminants and fragile areas. Inequalities of more than 10 mm correct cement-sand solution a day before the work began. If necessary, strengthen the soil of the G-1, according to the instructions. All preparation of the base should be performed in accordance with the requirements of DBN V.2.6-22: 2001, DSTU-N B A.3.1-23: 2013 and the requirements of the technological regulation of the installation of insulation systems for facades BETOL.

preparing

Gradually pour the mixture into a vessel with a measured amount of pure water while simultaneously manual or mechanical (at low revolutions), stirring until a homogeneous mass is obtained. Stand for 5 minutes and mix again.

Technical parameters

Usage guide

  • SUMISH K-9 "BETOL" C.1.ZK5 DSTU B V.2.7-126
    2011
  • Approximate dilution for bonding plates
    4.5-6.0 kg / m2;
  • Approximate dilution for reinforced layer
    4,5-5,5 kg / m2 at a layer thickness of 3-4 mm
  • Volume of water for mixing
    0,23 - 0,26 l / kg (about 6 l / bag)
  • Suitability of the mortar mixture
    not less than 2,5 hours.
  • Water absorption coefficient
    not more than 0,5 kg / m2 / h.
  • Correction time
    not less than 10 min.
  • Shrinkage
    no more than 1.5 mm / m
  • Strength of grip with concrete base
    not less than 0,5 MPa
  • Vapor permeability
    not less than 0,1 mg / mhh. x pa
  • Frost resistance
    not less than 50 cycles
  • Performance temperature
    from + 5 ° C to + 30 ° C
  • Packaging
    paper bags of 25 kg

Gluing heat insulation boards.

Plates to set horizontally along the length. Vertical sides are displaced relative to the adjacent slabs. Before sticking the plate to fit dry with a seam thickness of no more than 2 mm. At the corners of the buildings, the plates should be arranged with dressing. The first layer of plates should be at a height of 50 cm from the ground. When glued on even surfaces, apply glue to the entire surface of the board with a spatula with a size of teeth 10x10 mm. For uneven surfaces, apply a slab along the perimeter of the plate at a distance of 3 cm from the edge with ruptures, so that air cork does not appear. At the center of the plate to form 3-5 lumps of glue so that the surface glued is not less than 50% of the total. After applying the glue on the slide, slide it to press against the wall with an equal plane with adjacent slabs. Remains of glue on the ends to pick up. After 3 days, the inequalities between the plates must be removed using a grinder with a grinding net. After that, make mechanical fastening (duplication) and arrangement of the waterproof layer. The implementation of the protective reinforced layer is allowed not earlier than 3 days after bonding the slabs. When doing work recommended the use of a special grater, one side of which has square teeth 10x10 mm. Apply glue to the entire surface of the plate with a smooth side of the grater. Apply glue to the entire surface of the plate with a smooth side of the grater. Apply a continuous strip to the width of the reinforced mesh. Form the crests with the toothed side. Hold the grinder at an angle of about 60 ° to the slab. Smoothly squeeze the mesh into glue and smooth to make the grid completely drowned in glue. Do not allow wrinkles and blistering. Overlapping adjacent strips of the grid should be at least 10 cm. Application of subsequent coatings on the created reinforced layer is allowed not earlier than 3 days. When performing work during the first 3 days, do not allow the drying of the surface.

Store in dry containers in unharmed containers. Warranty period - 12 months from the date of production.

The technical characteristics of the mixture and the recommendations for use were determined under standard conditions (t = 20 ° С, humidity 65%) and in real conditions may change.

Download full catalog in PDF format
download