UKEN

Thank you!

Our manager will contact you as soon as possible

К- 10 Glue of "SUPER FLEX"

for ceramic granite, granite, slabs of super size, stone and warm floors
description:

К-10 - a cement-sand mixture with fillers and modifiers for gluing of any kinds of finishing materials: ceramic tile, ceramic granite, mosaic, gres, boards of supersize, decorative stone.

features:
  • For external and internal works
  • Elastic
  • Water-repellent, frost-resistant
  • Increased adhesion to any of the bases
  • For slabs of large sizes
order

Usage

К-10 - a cement-sand mixture with fillers and modifiers for gluing of any kinds of finishing materials: ceramic tile, ceramic granite, mosaic, gres, boards of supersize, decorative stone. Resistant to deformations, temperature fluctuations, variable water impact. Suitable for floors with heating (with any type of heating elements), for facing of pools, fountains, basements of buildings, staircase marches, both in the middle and outside of the premises.

preparing basis

The base should be solid, level, cleaned of contaminants and fragile areas. Inequalities of more than 10 mm correct cement-sand solution a day before the work began. If necessary, strengthen the primer G-1, according to the instructions. Concrete surfaces are treated with adhesive paint BK-1 "BETONKONTAKT".

preparing

Gradually pour the mixture into a vessel with a measured amount of pure water while simultaneously manual or mechanical (at low revolutions), stirring until a homogeneous mass is obtained. Stand for 5 minutes and mix again.

Technical parameters

Usage guide

  • SUMISH K-10 Q.1.3K4 DSTU B V.2.7-126
    2011
  • Approximate dilution
    from 1.5 kg / m2 at a layer thickness of 1 mm
  • Volume of water for mixing
    0,17-0,20 l / kg (4,25-5,0 l / bag)
  • Suitability of the mortar mixture
    not less than 2,5 hours.
  • Correction time
    not less than 15 min.
  • Open time
    at least 20 min.
  • Strength of the clutch with the base
    not less than 1.2 MPa
  • Time of possible technological movement
    no later than 48 hours.
  • Performance temperature
    from + 5 ° C to + 30 ° C
  • Guaranteed storage life
    12 months. from production date
  • Packing
    25 kg bag

Apply a thin layer of glue to the prepared leveling base and re-form it with a toothed spatula. Spatula hold at an angle of about 60 ° to the base. Apply the tile, pressing it to the glue with a light sliding motion. When facing with a rough stone or tile over 300x300 mm, apply a two-sided bonding technique: apply a mortar mixture with a thin layer (about 1 mm) to the tile, as well as to the prepared surface and form a toothed spatula.

Recommended spatula teeth size:

Tiles to 150x150 mm - teeth 6x6 mm

Tiles up to 200x200 mm - teeth 8x8 mm

Tile to 300x300 mm - teeth 10x10 mm

Tile more than 300x300 mm - teeth 12x12 mm

You can adjust the position of the tile within 15 minutes. In dry and windy weather it is recommended to apply a mortar mixture on small areas. Warping and moderate surface treatment are possible after 48 hours. Do not moisten the tile before use. The thermal load of the "warm floor" system is allowed not earlier than 28 days after the cladding.

The technical characteristics of the mixture and the recommendations for use were determined under standard conditions (t = 20 ° С, humidity 65%) and in real conditions may vary.
The manufacturer guarantees the conformity of the products with the declared technical characteristics, subject to the rules of transportation, storage and compliance with this instruction.
The manufacturer does not bear responsibility for the unauthorized use of the material.

Download full catalog in PDF format
download